How to use autoclaveHow to connect to city electricityConnect the device to the wall outlet after ensuring that the wall is plugged in. The autoclave works with 220 volts and a frequency of 50 Hz, and volatility of 180 to 220 volts will not cause any problems in the operation of the autoclave. If the voltage changes are too high then you should use an appropriate transformer. It should be noted that the wiring of the machine must be at least 2 mm in diameter.
How to open and close the autoclave door1. To open and close the autoclave, first add 3 drops for a 10-liter autoclave, 5 for the 25-liter autoclave, and 7 for the autoclave for 50 and 75-liter movable gangways, then open the stack with a red collet to open it to The door is raised and is about 1.5 to 2 inches away from the autoclave.
2. To close the autoclave door, first close the fixed flange with a red loop (hinge) to sit up to the autoclave, then place and close the rest of the gates.
How to drip autoclavesFirst, open the door, remove the tray and then pour the top of the max plate into the water container, then insert the tray into the machine and put the equipment inside the autoclave and then close the door. If the machine does not have enough water, it can be seen on the error-1 screen and the water LED is OFF. If the water is sufficient, the LED of the water will be ON WATER.How to use autoclaveAt this time, the autoclave is adequately drained and you can adjust and use the sterilized duration as described below. (It should be noted that the programs set on the autoclave and the answer to your work) will first ON / OFF the ON switch. In this case, because the device is sufficiently watertight, the LED lights up, and the internal temperature of the device appears on the display screen. In this situation, the programs set up on the electronic board will continue the steps to automatic alignment. Just press the Start button to start the machine.If you need to change the time of sterilization, do the following: first, turn on the POWER key, press the SET key, and set the display to 15:00. Once again, you can set the SET key with UP / DOWN keys. After setting the desired time, press the SET key 3 times to turn the display back on and ready to be restarted and store the time in memory. After setting the desired program, press the START key. The display first comes in – and then the device element starts, when the HEATER and WATER lights are on and the temperature of the machine reaches 121/5 when the autoclave is turned on. The HEATER light goes off and the STERILL ST illuminates and the sterile timer starts to work in reverse.If you need to see the duration of the sterility, press the TIME / DOOR key to show you the remaining sterile time, and after 15 seconds it will go back to you first and show the autoclave’s temperature . At the end of the sterile time, the LED of the heater is switched off and on the display screen, with the interrupted beep being heard, such as ENDOFSTERILE, and the STERILE END LED lights up. In this case turn off the POWER switch. Open the steam drain valve on the door to completely evaporate the steam and reach the zero pressure on the door. Then open the autoclave door.
How to open and close the autoclave door1. To open and close the autoclave, first add 3 drops for a 10-liter autoclave, 5 for the 25-liter autoclave, and 7 for the autoclave for 50 and 75-liter movable gangways, then open the stack with a red collet to open it to The door is raised and is about 1.5 to 2 inches away from the autoclave.
2. To close the autoclave door, first close the fixed flange with a red loop (hinge) to sit up to the autoclave, then place and close the rest of the gates.
How to drip autoclavesFirst, open the door, remove the tray and then pour the top of the max plate into the water container, then insert the tray into the machine and put the equipment inside the autoclave and then close the door. If the machine does not have enough water, it can be seen on the error-1 screen and the water LED is OFF. If the water is sufficient, the LED of the water will be ON WATER.How to use autoclaveAt this time, the autoclave is adequately drained and you can adjust and use the sterilized duration as described below. (It should be noted that the programs set on the autoclave and the answer to your work) will first ON / OFF the ON switch. In this case, because the device is sufficiently watertight, the LED lights up, and the internal temperature of the device appears on the display screen. In this situation, the programs set up on the electronic board will continue the steps to automatic alignment. Just press the Start button to start the machine.If you need to change the time of sterilization, do the following: first, turn on the POWER key, press the SET key, and set the display to 15:00. Once again, you can set the SET key with UP / DOWN keys. After setting the desired time, press the SET key 3 times to turn the display back on and ready to be restarted and store the time in memory. After setting the desired program, press the START key. The display first comes in – and then the device element starts, when the HEATER and WATER lights are on and the temperature of the machine reaches 121/5 when the autoclave is turned on. The HEATER light goes off and the STERILL ST illuminates and the sterile timer starts to work in reverse.If you need to see the duration of the sterility, press the TIME / DOOR key to show you the remaining sterile time, and after 15 seconds it will go back to you first and show the autoclave’s temperature . At the end of the sterile time, the LED of the heater is switched off and on the display screen, with the interrupted beep being heard, such as ENDOFSTERILE, and the STERILE END LED lights up. In this case turn off the POWER switch. Open the steam drain valve on the door to completely evaporate the steam and reach the zero pressure on the door. Then open the autoclave door.